I1 /U67GT/I1 3G 双系统刷机教程准备以下设备：U盘*2

I1 /U67GT/I1 3G 双系统刷机教程
准备以下设备：
U盘*2 USB-HUB*1 USB键盘*1 机器必须为2+32G的配置
一．刷BIOS
1.将BIOS文件拷到U盘中，用OTG将U盘连接到机器上

2.找到0_flash.bat 文件，鼠标右键（触摸长按）然后选择以管理者方式运行，如下图：
3.运行后会出现如下出口，点击“是”

4.然后机器会自动刷BIOS，一直到提示“按任意键退出”，这时将机器关机。
二、刷安卓系统
1.将安卓目录下的文件拷贝到U盘的根目录下（注：需没有做过WIN8刷机系统盘的U盘才能使用）,并将U盘命名为UUI：
2.准备好，USB-HUB OTG线 键盘，然后将拷贝好安卓文件的U盘，和键盘接入到USB-HUB上，然后通过OTG将HUB链接到机器。关机状态下，按住音量减键不放再按power键开机。同时按键盘上的“ESC”键进入BIOS界面。如下图：

3.选择boot----QUIET Boot将其从enabled模式切换为disabled模式如下图：
4.然后选择save&exit------点击倒数第二项“lanuch EFI shell from filesystem device”进入刷安卓系统界面如下图：

5.刷机成功后，机器将会自动开机。
三、刷WIN8 系统
1.将U盘格式化为NTFS格式，然后WIN8目录下文件拷贝到U盘的根目录下，并将U盘命名为WINPE：
2.将U盘接到OTG上然后连接到机器上
3.将机器开机（若机器已开机，在安卓系统下，直接将机器重启即可）出现如下界面，选择WIN8系统图标，然后点击图标下面的SURE。机器将会自动进入刷机界面，刷机成功后机器将会自动开机。如下图：



四、注意事项
1.必须按以上步骤，一刷BIOS，二刷安卓，三刷WIN8
2.机器存储必须为2+32G
3.若想重新刷安卓，刷安卓后会把WIN8系统格掉，所以WIN8也需要重新刷（所以想重新刷安卓的朋友，若WIN8系统上有重要资料，请先备份)
4.WIN8可以反复刷机，具体操作如下：
A、将U盘格式化为NTFS格式，然后将以下文件拷贝到U盘的根目录下：
B、准备好，USB-HUB OTG线 键盘，将拷贝好安卓文件的U盘，和键盘接入到USB-HUB上，然后将HUB通过OTG连接到机器上。
C、将机器开机，同时按键盘上的F7键。选择你的U盘，然后按回车键。此时机器将会进入刷机界面自动刷机。刷机成功后机器会自动开机
5.安卓盘一定要是没有做过WIN8刷机系统盘的U盘才能使用
6.安装双系统时机器务必保证机器的电量在30%以上，否者更新bios失败可能导致机器无法启动。

Hasil (Inggris) 2:

I1 / U67GT / I1 3G dual system Brush tutorial
the following equipment:
U disk * 2 USB-HUB * 1 USB keyboard * 1 Machine must be 2 + 32G configuration
a. Brush BIOS
to BIOS file copying 1. U disk, with OTG U disk connected to the machine 2. Find 0_flash.bat file, right-click (touch long press) and then select Run as administrator mode, as shown below: 3. After running as exports appears, click "Yes" 4. Then the machine will automatically brush BIOS, until the prompt "Press any key to exit", then the machine is turned off. Second, brush Andrews Andrews directory 1. Copy the files copied to the root directory of U disk (Note: the need to have done in order to use U disk WIN8 brush system tray), and U disk named UUI: 2. Prepare Well, USB-HUB OTG line keyboard, U disk and then copy the good Android file, and keyboard access to a USB-HUB, and HUB by OTG will link to the machine. Shutdown mode, press and hold the volume down button and hold power button to boot. Press "ESC" key on the keyboard to enter the BIOS interface. As follows: 3. Select the boot ---- QUIET Boot mode will switch it from enabled to disabled mode as shown below: 4. Then select save & exit ------ Click penultimate "lanuch EFI shell from filesystem device" enter Brush Android interface as follows: 5. Brush successful, the machine will automatically boot. Third, brush WIN8 system 1. The U disk formatted as NTFS, and then copy WIN8 catalog file to the root directory of U disk and U disk named WINPE: 2. U disk connected to and then connect to the OTG the machine will boot the machine 3. (If the machine is switched on at the Andrew system, directly to the machine can restart) the following interface, select WIN8 the System icon, then click on the icon below SURE. The machine will automatically enter the brush machine interface, after the success of Brush machine will automatically boot. As follows: IV Notes 1. You must press the above steps, a brush BIOS, two brush Andrews, three brush WIN8 2. machine memory must be 2 + 32G 3. To re-brush Andrews, Andrews will WIN8 brush system format off, so WIN8 also need to brush (so I wanted to re-brush Andrews friends, if there is important information on WIN8 system, please backup) 4.WIN8 can repeatedly brush, as follows: A, U disk formatted as NTFS and then copy the following files to the root directory of U disk under: B, ready, USB-HUB OTG line keyboard, U disk copy good Android file, and keyboard access to the USB-HUB, HUB then by OTG connected to the machine. C, the machine is turned on, press the F7 key on the keyboard. Choose your U disk, and then press Enter. At this point the machine will enter the brush machine interface, automatic brush machine. Brush successful machine will automatically boot disk must be a 5. Andrew has not done WIN8 brush system disk U disk to use when installing the two systems 6. The machine must ensure that the machine power more than 30%, not those who failed bios update may cause the machine Can not start.

Hasil (Inggris) 3:

3G /U67GT/I1 I1 double brush system tutorial
to prepare the following equipment:
U disc * 2 USB USB-HUB*1 keyboard * 1 machine must be 2 32g configuration
a. Brush BIOS
1. the BIOS file copied to the U disk, U disk connected to the machine

2. Find 0 0_flash.bat file mouse right key (touch long press) and then choose to management mode of operation, as shown in the following picture. Operation will appear as follows export, click "yes"

4. then the machine will automatically brush BIOS, to prompt "press any key to exit", then the machine shutdown OTG.
two, brush the Android system
1.Will Android directory files are copied to the U disk root directory (Note: not done win8 brush system disk U disk to use), and U disk named UUI:
2. Ready, usb-hub OTG cable keyboard, and then copy Ann Zhuo file U disk, and keyboard access to the usb-hub and OTG will hub links to the machine. Shutdown state, press and hold down the volume keys to press power key to start. At the same time, press the "ESC" button on the keyboard to enter the BIOS interface. The following figure:
boot----QUIET select Boot
3. to switch from enabled to disabled mode:
4.Then select the save / exit------ click the second last item "lanuch EFI shell from the filesystem device" into the brush Ann Zhuo system interface as shown below:
brush
5. machine successfully after machine will automatically boot.
3, brush win8 system
1. Would U disk formatted for the NTFS format and win8 directory under the file copy to the root directory of the U disk, and U disk named for WINPE:
2. U-disk received OTG and connect to the machine. The machine starts (if the machine is switched on, in the Android system, directly to the machine you can restart) the following interface, select the win8 system icon, and then click on the icon below for sure.The machine will automatically enter the brush machine interface, the machine will automatically start after the brush machine. As shown below:



4, attention matters
1. Must be in accordance with the above steps, a brush BIOS, brush the second Android, three brush WIN8
2. machine storage must be for 2 32G
3. if you want to re brush Android, brush Android after the win8 system price to sell, so the win8 also need to re brush (so I want to re brush an excellent friends, win8 system if there are important information, please back up)
4.WIN8 can be repeatedly brush, specific operation as follows:
A, U disk is formatted to NTFS format, then the following files are copied to the U disk root directory:
B, readyOTG USB-HUB line keyboard, will copy the U disk, and keyboard access to the USB-HUB, and then the HUB is connected to the machine via OTG.
C, the machine will start, and press the F7 key on the keyboard. Select your U disk, and then press enter. At this point the machine will enter the brush machine interface. After the success of the brush machine will automatically boot
5. Zhuopan if not done win8 brush system disk U disk to use
6. installed dual system machine must ensure that the machine electricity in more than 30%, or update the BIOS failure may cause the machine could not be started.